Includes a $55 establishment fee and $65 annual fee ($32.50 half-yearly). Standard interest rate (currently 29.49% p.a.)
applies after the Interest Free term ends. *Paying only the minimum monthly repayment of 3% of the outstanding monthly balance
or $20 (whichever is more) may not be sufficient to repay the purchase amount(s) during the Interest Free term. Further
information on rates and fees is available at
gemfinance.co.nz. Credit provided by Latitude Financial Services Limited.
Give both sleepers a proper bed at camp. Pair the CloudMat PRO Queen’s 15 cm of cushioning with the raised Quick Set Queen Stretcher for a comfortable setup for two.
What’s included
1 × CloudMat PRO Queen Sleeping Mat with a 202 × 150 cm queen sleeping surface.
1 × Quick Set Queen Stretcher with its carry bag and under-bed mesh pocket and side pouch.
Specifications
Inflated mat dimensions (L × W × H)
202 × 150 × 15 cm
Packed mat dimensions (L × W × H)
75 × 40 × 40 cm
Mat weight
10.4 kg
Open stretcher frame (L × W × H)
216 × 141 × 47 cm
Sleeping capacity
Two adults
Mat inflation
Self-inflating
Stretcher weight
15 kg
Stretcher maximum load
300 kg combined
Size guide
Leave room around the setup for tent access and gear.
Instructions
Follow these steps for the CloudMat PRO Queen and King Single. Repeat the valve steps for each valve fitted to your mat.
Before your first trip
Unpack and unroll the mat at home. Give the foam time to recover from being compressed in its packaging, then check that the mat inflates and that the valves close properly. The first inflation, or inflation after a long period packed away, can take longer.
Set up the stretcher
Fully open the Quick Set stretcher on firm, level ground. Check that its frame is completely opened and stable, then lay the CloudMat PRO on top with the sleeping surface facing upwards and the valves accessible. Inflate the mat using the steps below. Pack the mat and stretcher separately after use.
Faster self-inflation
Unroll the mat fully on a clean surface and remove the valve caps.
Turn each valve insert to the open position shown in the photo below. This position allows air to enter freely for faster self-inflation.
Leave the mat unrolled and let the foam expand and draw air in. Keep weight off the mat while it fills.
Once the mat has expanded, turn each valve to Inflate mode, then close the valves and refit the caps before use.
Inflate mode and closing the valves
Use the photo above to identify Inflate mode. You can also let the mat self-inflate in this position. After using the faster open position, return each valve to Inflate mode before closing it and fitting its cap. Check that every cap is seated securely.
Check the comfort
Lie on the mat to check the firmness. For a softer feel, briefly open a valve in Deflate mode and release a little air at a time. Return it to Inflate mode, close the valve and refit the cap before lying down again.
Deflate and pack away
Brush off dirt and allow the mat to dry before packing it.
Remove the caps and turn the valves to Deflate mode, matching the photo above.
Roll the mat slowly towards the valve end, applying steady pressure to push the air out as you roll.
If the roll is still too bulky for the carry bag, unroll it with the valves in Deflate mode and roll it again to expel more air. Follow the mat’s original folding pattern where needed to match the width of the bag.
Keep the roll compressed while you close the valves and refit the caps.
Place the rolled mat in its carry bag for transport.
Cleaning and storage
Wipe the fabric with a damp cloth and mild soap. Keep grit away from the valve openings and seals.
Let the mat dry completely before putting it away.
Between trips, store it unrolled with the valves open in a dry place where possible, so the foam can retain its loft.
Keep it away from prolonged direct sunlight and sharp objects.
If inflation seems slow or the mat loses firmness
Check that the valve inserts are in the intended position and that the openings are clear. Allow extra time for foam that has been compressed in storage. If the mat loses air after closing, check every valve and cap for a secure seal and remove any grit from the sealing surfaces.
Eligible items can be returned within 30 days of purchase, unused with original packaging and labels. There is no handling or restocking fee. Return postage is at your cost; conditions apply.
Contact us before sending anything back, with your order details, photos and a brief description of the issue. We will help with warranty, repair or spare-part options. Coverage varies by product; your consumer rights still apply.
Our target is 1–2 business days after dispatch for in-stock, standard parcels. Rural, remote and bulky deliveries can take longer. Preorders, public holidays and carrier delays may affect timing. Contact us if you need an item by a specific date.
Standard NZ shipping is $10, or free on orders over $150, excluding large items. Product-specific freight or remote-area surcharges may apply. Final shipping charges are shown at checkout.
Yes, tracking details are sent by email when your order is dispatched. Allow time for the carrier’s first scan. If you cannot find the email, contact us with your order number.